- Vcds 12.12 clone how to#
- Vcds 12.12 clone serial number#
- Vcds 12.12 clone install#
- Vcds 12.12 clone update#
- Vcds 12.12 clone upgrade#
Actia Multi-Diag II 2012 v.26.08.1 + Service Pack 2 v.26.25 + Vivid WorkShop 8. Actia Multi-Diag II 2011 v.23.07 + Vivid WorkShop 5. Added to MY COLLECTION for CDP and CDP+ Firmware 1515 from Wurth Group for WOW and W.EASY CDP+ Recovery, OTP Area, Firmwares NEW.txt MY CDP AND CDP+ COLLECTION.txtĪCTIA MULTI-DIAG COLLECTION 2009 2010 2011 2012 2013 2014 2015 So, Long Story Short, what you Will Find Inside: 1. Added to MY COLLECTION for CDP and CDP+ Firmware 14 from Wurth Group for WOW and W.EASY 14.
Vcds 12.12 clone install#
Added MY COLLECTION for CDP and CDP+ where you will find all above + Complete Install kits to Delphi and Autocom 2013.3, All my WOW 4 and 5 Collection, All Genuine Kits of 2014 and also The mixed 2014.1 Version with 2 patches(one already present in main archive and another one separated) - a little late but i forgot to post this also here. Added to MY COLLECTION for CDP and CDP+ Firmware 1513 from AUTOCOM 2015 R1 2.15.1 12. If you need a password for a file, like always it's fantomel 11.
All you need to play with your CDP+ interface it's a ST-Link V2 Programmer CLONE like these HERE or the Original. included and all from 1->9 If you find something wrong or to add to this pack please write. My flash files written to CDP+ by WOW and read via ST-Link saved as.
Vcds 12.12 clone upgrade#
Firmware recovery to flash your CDP+ interface in case of upgrade or bad flash: a) Old ones already on web:2012.2 2012.3 2013.1 2013.2.1 2013.2.2 2013.3. Firmware from programs: 1321 from WOW 1331 from delphi, autocom, wow 1410 from WOW, 1422 from Delphi and 1423 from Autocom. STM32 ST-Link Utility v3.4.0 to read firmware and otp and if you are willing to risk to change them. Flash Loader Demonstrator v2.6.0 to restore your firmware via USB 6.
Vcds 12.12 clone serial number#
This area can be modified only by incrementing the actual serial number in the already written ST chip or you can write any number in a new one if you know how.
Vcds 12.12 clone how to#
How to read the OTP (One Time Programming) area responsable for the serial number of your interface - BE CAREFUL. How to read your firmware with a ST-Link device via CDP+ J400 connector and also pinout of STLink to J400 4. How to recover your CDP+ from a bad flash or red lights problem via USB. Mprog 3.5 and ept file for CDP+ (never seen one that has this problem) 2. Story short, what will you find inside this pack: 1. We (at least me) prefer to write the firmware with WOW because like this i can use wow and delphi-autocom without problems since WOW writes some extra bits that delphi-autocom does not detect but wow does. As you all know we can flash our interface SAFE only inside Delphi 2012.3 (last version without clone blacklist) or in these days inside WOW (no matter what version).
Vcds 12.12 clone update#
… just dismiss that message do not reboot the interface at this time.ħ) Click on the Update tab and then click the button.CDP+ Delphi Autocom Firmware Recovery,OTP Area,Firmwares So i was thinking these days to make a full pack at day regarding the the firmware our CDP+ interfaces. If you get a MessageBox indicating that VCIConfig can’t read the current versions like this: If it doesn’t, unplug the interface and try a different USB port (assuming the computer has more than one), then click.
VCIConfig should find the interface and show you its serial number.
Or you can start it directly in your VCDS folder: There should be a shortcut to it in your Windows Start menu:
This is rare with “home” routers, but somewhat more common with those installed in corporate environments.ĥ) Plug your interface into a USB port on the computer.Ħ) Start VCIConfig manually. Note: Some routers can also be overly aggressive about blocking outbound traffic. The current version of the VCDS Installer takes care of that for you if you don’t un-check the relevant option. Installing Windows on a Mac using Boot Camp will also work.ģ) Make sure you have a current version of VCDS installed.Ĥ) Make sure that the PC has internet access and that Windows Firewall isn’t blocking our software’s access to our server via TCP port 11,000. No, not a Mac running Windows in a VM we need a machine that runs Windows natively. If the other end is plugged into a car, pull the interface out of the car’s OBD-II port. If it’s plugged into a computer, unplug the USB cable from the computer. Here’s what you need to do:ġ) Unplug your interface from all sources of power.